Reinitialize Your Holosun EPS Carry Red Dot Scope

Need to nullify your Holosun EPS Carry Red Dot's settings? A factory reset will be just the trick.

Before you begin, make sure your sight is powered deactivated. Now, let's get into the process:

Squeeze down both the up and down buttons simultaneously.
During keeping those buttons held, activate the power switch on your Holosun EPS Carry Red Dot.
Theoptic will show a flashing indicator, showing that the reset process is in progress.
Sustain holding the buttons for around 5 seconds. Then, let go both buttons.
Your settings have been reset to their factory defaults.

Go ahead adjust your Holosun EPS Carry Red Dot to your desired setup.

Resetting Your Holosun EPS Carry to Default Settings

Sometimes your Holosun EPS Carry optic might require a return to factory to its default settings. This is typically done when the optic's performance is unexpected. There's how to reset your Holosun EPS Carry:

First powering off your optics
Find the small switch on the side of the optic.
Pressduring this control for approximately 5 seconds. This will initiate a factory reset
After the optic's display indicates that it has been reset, you can stop pressing the switch and power it back on.

Your Holosun EPS check here Carry should now be operating at its default settings. At this point follow the manufacturer's guidelines for adjusting reticles your optic to your specific weapon system.

Restore Your Holosun EPS Carry: A Step-by-Step Factory Procedure

Need to get your Holosun EPS Carry back to its default settings? A factory reset can be a helpful solution when you're experiencing issues or simply want a clean slate. Thankfully, the process is straightforward.

Begin by powering off your Holosun EPS Carry.
Then Function switch and Press the power switch/button.
Keep holding both buttons for approximately 5 seconds until you see a pulsating light on the display.
Let go of both buttons/keys to complete the factory reset. Your Holosun EPS Carry will now be back to its original settings.

Return to Factory Defaults : Holosun EPS Carry Red Dot

Resetting your Holosun EPS Carry red dot sight to factory defaults can be a valuable option for troubleshooting issues or refreshing its performance. This process effectively erases all customized settings, returning the device to its original configuration.

To initiate this reset, you'll need to locate the designated button on your Holosun EPS Carry. Consult your user instruction booklet for precise information. Generally, a brief press and hold of this button will initiate the factory reset process. You'll likely see a sequence of visual cues to confirm that the reset is successfully in progress.

Executing a Factory Reset for the Holosun EPS Carry Sight System

If you're experiencing issues with your Holosun EPS Carry Sight System or simply want to set back it to its original settings, a factory reset might be the solution. This process will completely erase all user-configured settings and bring back the sight system to its initial state. Before proceeding, ensure you understand that this action is irreversible and will remove any personalized adjustments you've made.

In order to perform a factory reset, follow these instructions:

Firstly identifying the reset button on your Holosun EPS Carry Sight System.
Then, apply a small, pointed object like a pen or paperclip to depress the reset button.
Maintain the reset button for about 5 seconds.
The device will indicate a message indicating that the factory reset is finished.
Upon completion of the reset, your Holosun EPS Carry Sight System will go back to its factory settings.

System Reset for Your Holosun EPS Carry Fast

Resetting your Holosun EPS Carry to factory settings is a basic process that can solve any issues you may be facing. Here's how to perform a quick and hassle-free reset:

Initially turning your Holosun EPS Carry on.
Then, press and hold the mode button for approximately 10 seconds.
You'll a flashing light or display, signifying that the reset is in motion.
Continue holding the button until the configuration are confirmed.
The Holosun EPS Carry will now be reset to factory settings.